PCB Reverse Engineering
Turn your physical PCBs into usable CAD data: Gerber files, drill data, netlists, BOMs and native schematics. Have us reverse engineer your boardBring reverse engineering in-houseRegain control of your legacy designs. Whether you’re facing a data disaster, human error, obsolescence, or a merger or acquisition that left the records incomplete, we restore your ability to manufacture, troubleshoot and repair. We convert a physical printed circuit board, bare or assembled (PCBA), into accurate fabrication files and schematics, so you avoid the cost and risk of starting from scratch. Because the data comes from the real board at calibrated accuracy, the replacement keeps the original’s exact form, fit and function.
We can do it for you, or equip your team to do it in-house. Either way, you get the same deliverables and regain control of your data.
Years of Support with Global Partners
Countries with systems in use
NIST-traceable calibrated accuracy
registered service operations
When you need PCB reverse engineering
Electronics outlive their documentation. The CAD data is lost, wrong, or was never in your possession; the original supplier is gone; a part is obsolete; or a board failed and you need to see what’s actually inside it. When no spares exist, the system it lives in goes down.
Our PCB reverse engineering capabilities include:
File recovery
restore lost Gerber data, netlists and schematics, and verify your IP.
Obsolescence management
reproduce discontinued and out-of-stock boards.
Design restoration
rebuild missing schematics and BOMs from the existing board.
Repair support
get the schematic and data your team needs to start diagnosing a board when the documentation is gone.
Because the data is extracted from the real board, an exact-match replacement generally doesn’t trigger new UL, CE, EMI or signal-integrity certification the way a redesign would. For regulated programs, avoiding recertification is often worth more than the hardware.
We serve aerospace, defense, nuclear energy, medical, automotive, mass transit, telecommunications and contract manufacturing, including installations across the Air Force, Navy and Army, the FAA, and DoD and government-approved contractors.
How it works: one board, start to finish
The best way to show how PCB reverse engineering works is to do it. Below is ScanCAD’s own 3.5″ × 3.5″, four-layer sample board, taken from a physical artifact to a complete data package, with the real output from every step. Your team can run these same steps on a ScanFAB system, and our Service Bureau brings decades of refined process to the boards that need it most.
Step One: Intake and documentation
We document the board as received: high-resolution scans of both sides, dimensions and layer count. Every component is identified and researched, and the bill of materials is compiled with manufacturer part numbers and datasheets.
Step Two: Component removal and surface preparation
Components are removed, and our precision material removal system strips soldermask and silkscreen without damaging the copper underneath. The exposed outer copper is then scanned on a NIST-traceable calibrated scanner.
Step Three: Layer-by-layer delamination and scanning
For a multilayer board, we remove material one layer at a time and scan each newly exposed copper layer at the same calibrated accuracy. Every layer is captured, including inner and dielectric layers (the dielectric shows exactly where each drill passes) and the copper around blind and buried vias.
Step Four: Gerber and drill generation
Our ScanFAB software converts the calibrated layer images into Gerber RS-274X data for every copper layer, plus soldermask, silkscreen and board outline. Built-in quality checks catch shorts, opens, clearance problems and layer-to-layer misregistration in the data, not on the fab line. Drill data covers every hole. On the sample board that’s 50 plated through-holes in five sizes, four non-plated mounting holes, and a blind via between layers 3 and 4. That’s a light load for the software, which handles far denser drill sets.
Step Five: Virtual PCB reconstruction and netlist
The layers, drill data and components are assembled into a virtual reconstruction of the board. From it we extract the full netlist and component placement. Where you need independent confirmation, connectivity can also be validated electrically with a flying-probe tester (a Service Bureau service using third-party equipment; flying-probe testers aren’t a ScanCAD product, so ScanFAB customers source their own).
Output: netlist and placement data in IPC-D-356, IPC-2581, ODB++ and GenCAD.
Non-destructive option: the same netlist can be extracted from the bare board by flying-probe testing, and we build the schematic from there.
Step Six: Schematic generation
The netlist and BOM become a native, editable schematic in your design tool’s format, plus a shareable intelligent PDF.
Output: native schematic (the sample includes OrCAD) and PDF. Auto-generated schematics are formatted for utility; cleanup to your own drawing standards is available as a Service Bureau service. Need a fully editable board layout as well? Native eCAD layout is available as a Service Bureau deliverable.
The result is a complete Technical Data Package.
Everything an engineer, fabricator or assembler needs to build the board again, with exact form, fit and function.
What you get
Every project delivers production-ready data that works with modern manufacturing and CAD systems, tailored to the outputs you need.
Deliverable | What it is | Formats |
|---|---|---|
| Bare board fabrication data | Every copper layer, soldermask, silkscreen and board outline | Gerber RS-274X, ODB++, IPC-2581, GenCAD, DXF |
| Drill data | Through-hole, blind and buried vias | Excellon II (.HDT, .HDF), Sieb & Meyer, and many more; ask if yours isn’t listed |
| Netlist | The electrical connectivity of every pin | IPC-D-356, IPC-D-356A, IPC-2581, ODB++, GenCAD, FATF |
| Component and assembly data | X/Y centroid, rotation and board side for every part; pick-and-place programs | ASCII and CSV pick-and-place, component centroid data |
| Bill of materials | Every component, with manufacturer part numbers and datasheets where available | .XLSX |
| Schematic | Native, editable schematic plus a shareable intelligent PDF | OrCAD, Altium, PADS, KiCad, Eagle, and other formats; PDF |
| Native board layout (optional; Service Bureau only) | A fully editable layout in your ECAD tool, linked to the schematic and BOM | See Native eCAD Layout |
| Technical data package | All of the above, organized for archive and re-procurement |
Don’t see what you need?
Let’s talk about additional output formats.
Destructive and non-destructive reverse engineering
We offer both methods, and we’ll tell you up front which one fits your board and your goal. We can also work from original films, mylars and artwork drawings. If you still have the original films, they’re often an even better starting point than the board.
Destructive (full layout recovery)
This is the process shown above, and the one most projects use. The board is prepared and delaminated layer by layer, and each layer is imaged on our NIST-calibrated scanner. It captures every circuit layer, including complex inner layers, with exact copper geometry that matches the original board’s form, fit and function.
- All circuit layers captured, including inner layers
- Blind and buried via detection
- Exact copper geometry replication
- NIST-traceable measurements: ±0.0010″ (±0.0254 mm) calibrated accuracy
- Proven on boards with 28+ layers by our Service Bureau; no practical layer limit exists in the software
Non-destructive (connectivity only)
When the bare board has to survive, we use flying-probe testing. Components are removed, but the bare board stays intact. This method captures connectivity, not inner-layer copper geometry. It delivers a validated netlist and an ECAD schematic you can use for a new layout, engineering models, or troubleshooting and maintenance documentation.
The tradeoff is simple: non-destructive gets you the circuit, and destructive gets you the board itself.
Lost PCB file recovery
If your original design files are gone, we recover lost Gerber files and recreate complete manufacturing data sets from your physical board, even if you only have a single sample.
Partial data recovery. Have some files but not others? We fill the gaps:
- Have a BOM only? We generate the Gerber data and schematic.
- Have Gerber data only? We create the schematic and netlist.
- Missing inner layers? We capture the complete layer stackup.
- Need just one piece? We can deliver any single item, such as a netlist from your Gerber data, with no schematic required. Each output needs the right inputs (a schematic needs both a BOM and a netlist, for example), and those can come from us, from you, or a mix.
- Already own a ScanFAB system? Our Service Bureau can take overflow work: you keep the parts you’re confident in, and we handle the rest.
We do it for you: ScanCAD Service Bureau | You do it in-house: ScanFAB system | |
|---|---|---|
| Best for | One board, an occasional program, or ongoing DoD and high-turnover work; no capital purchase, and no staff to train, retrain or maintain | Ongoing reverse engineering, or boards that can’t leave your facility |
| Who runs it | ScanCAD engineers in our Conifer, Colorado lab, with 30+ years of expertise behind every deliverable | Your team, trained by ScanCAD |
| Data and security | ITAR-registered service operations; CUI handled in a dedicated CMMC enclave and a physically separated lab; working toward CMMC Level 2 | Fully air-gapped; no internet connection required, and your data never leaves your site |
| Cost model | Per project | Capital purchase with a perpetual software license; optional maintenance |
| What you need to start | The board, or original films, mylars or artwork that can be scanned to scale; photos of both sides; the layer count; and your ITAR/CUI status | ScanFAB system and PMRS from ScanCAD; you supply the PC, lab space and an air filtration system, and basic hand tools |
| Getting started | A ROM estimate within one business day of a complete Request a Quote submission | Self-install in a few hours; interactive virtual training included (graded quizzes and feedback from our trainer), on-site training available |
| Next step | Request a quote | Request a system quote |
Not sure which fits?
Send us your board details. We’ve done this work for decades and trained the teams who do it in-house, so we can tell you which route fits.
Who does the work?
ScanCAD has built reverse engineering systems and run a reverse engineering service bureau for more than 30 years, from our lab in Conifer, Colorado. We’re the company that commercialized PCB reverse engineering, and we still make the PCB reverse engineering software and PCB scanner systems, and own the full chain from scan to data, so every result is traceable, not best-effort.
Trusted where it counts
Our systems and services are used across Air Force, Navy and Army installations, the FAA, defense contractors and nuclear utilities, with systems in more than 50 countries.
Good to know before you start
- Full layout recovery is destructive. The standard process delaminates the board. If the board can’t be sacrificed, the non-destructive route recovers connectivity and a schematic, but not the copper layout.
- Schematics are auto-generated. They’re accurate to the netlist and formatted for utility. Cleanup to your own drawing standards is done in your native CAD tool and is available as a Service Bureau service.
- Some part numbers can’t be recovered. Conformal coating and intentional obfuscation (sanded or unmarked parts) can hide component markings. We’ll flag any part we can’t identify. That’s rarely a deal-breaker: a BOM with a few known unknowns is a major head start over having nothing.
- Turnaround depends on the board and the deliverables. We’ll give you a realistic schedule with your estimate.
- CT scans are an input, not a service. If you have viable CT scans of your board, we can import and use them. ScanCAD doesn’t provide CT scanning.
Frequently Asked Questions
What do you need from me to get started? Start with our Request a Quote form, and please don’t email board photos or technical data to our general inbox. Tell us whether the work is ITAR-controlled or involves CUI, how many boards you can supply, which deliverables you need, and which ECAD tool you use, and include photos of both sides and the layer count if you know it. We’ll send a rough-order-of-magnitude (ROM) estimate within one business day of receiving a complete request.
How long does PCB reverse engineering take?
It varies with the board’s complexity and the deliverables you need, so we’ll give you a realistic schedule with your estimate rather than a generic number.
How many boards do I need to send?
For full layout recovery, one board is enough, but it will be consumed by the process. If you have spares or need the original back, tell us and we’ll discuss the non-destructive route.
Will my board be destroyed?
For full layout recovery, yes. Each layer has to be exposed and scanned. Non-destructive reverse engineering keeps the bare board intact but recovers connectivity and a schematic, not the copper layout.
What file formats will I get?
Gerber RS-274X, Excellon drill, IPC-D-356, IPC-2581, ODB++, GenCAD, FATF, pick-and-place data, a BOM, and a native schematic in your design tool’s format, plus PDF. If you need another format, ask.
Is PCB reverse engineering legal?
Generally, yes, when you own the design, are supporting equipment you own, or have the rights to reproduce the board. We ask every customer to confirm they have the right to the data before we start. If you’re unsure, talk to your counsel.
How do you handle sensitive or export-controlled boards?
Our service operations are ITAR-registered. Controlled Unclassified Information (CUI) is handled inside a dedicated, access-controlled CMMC enclave, and sensitive work runs in a lab physically separated from our office space. We’re actively working toward CMMC Level 2 certification. If your data can’t leave your facility at all, our ScanFAB system runs fully air-gapped on your site.
Can you work from partial data?
Yes. If you have a BOM, Gerber data or some of the layers, we fill in what’s missing, or deliver just the piece you need, such as a netlist from your Gerber data. Each output needs the right inputs: a schematic, for example, needs both a BOM and a netlist, which can come from us, from you, or a mix.
Can I get an editable PCB layout, not just Gerber data?
Yes. Our Service Bureau can deliver a fully editable native board layout in your ECAD tool, linked to the schematic and BOM. Layout is a Service Bureau deliverable for now; it isn’t yet available on ScanFAB systems. See Native eCAD Layout.
Should I use your service or buy a system?
If you have one board or an occasional need, the Service Bureau is usually the faster, lower-cost route. It’s also the better fit for ongoing DoD programs and high-turnover teams, since there’s no staff to train, retrain or maintain. If reverse engineering is ongoing work for your team, or boards can’t leave your site, a ScanFAB system makes sense.
Systems and services: ScanFAB PCB reverse engineering system | Schematic Generation Module | ConvertPLUS ARE netlist and pin numbering | PCB delamination with PMRS | Conformal coating removal
Industries: Aerospace | Defense | Medical | Automotive | Nuclear Energy | Rail and Transit | Telecommunications
Our team is here to answer any questions that you may have.
It’s a great time to start a discussion around your unique needs. We look forward to hearing from you! Feel free to send us a message at [email protected]



